GAS TURBINE POWER PLANT:
A generating station which employs gas turbine as the prime mover for the generation of electrical energy is known as a gas turbine power plant.In a gas turbine power plant, air is used as the working fluid.The air is compressed by the compressor and is led to the combustion chamber where heat is added to air, thus raising its temperature.Heat is added to the compressed air either by burning fuel in the chamber or by the use of air heaters.The hot and high pressure air from the combustion chamber is then passed to the gas turbine where it expands and does the mechanical work. The gas turbine drives the alternator which converts mechanical energy into electrical energy.
It may be mentioned here that compressor, gas turbine and the alternator are mounted on the same shaft so that a part of mechanical power of the turbine can be utilised for the operation of the compressor.Gas turbine power plants are being used as standby plants for hydro-electric stations, as a starting plant for driving auxiliaries in power plants etc.
Schematic arrangement of a gas turbine power plant:
The schematic arrangement of a gas turbine power plant is shown in Figure below.
The main components of the plant are :
(i) Compressor
(ii) Regenerator
(iii) Combustion chamber
(iv) Gas turbine
(v) Alternator
(vi) Starting motor
(i) Compressor : The compressor used in the plant is generally of rotatory type.The air at atmospheric pressure is drawn by the compressor via the filter which removes the dust from air.The rotatory blades of the compressor push the air between stationary blades to raise its pressure.Thus air at high pressure is available at the output of the compressor.
(ii) Regenerator : A regenerator is a device which recovers heat from the exhaust gases of the turbine.The exhaust is passed through the regenerator before wasting to atmosphere. A regenerator consists of a nest of tubes contained in a shell.The compressed air from the compressor passes through the tubes on its way to the combustion chamber.In this way,compressed air is heated by the hot exhaust gases.
(iii) Combustion chamber : The air at high pressure from the compressor is led to the combustion chamber via the regenerator. In the combustion chamber, heat is added to the air by burning oil.The oil is injected through the burner into the chamber at high pressure to ensure atomisation of oil and its thorough mixing with air.The result is that the chamber attains a very high temperature (about 3000 F).The combustion gases are suitably cooled to 1300F to 1500F and then delivered to the gas turbine.
(iv) Gas turbine : The products of combustion consisting of a mixture of gases at high temperature and pressure are passed to the gas turbine.These gases in passing over the turbine blades expand and thus do the mechanical work. The temperature of the exhaust gases from the turbine is about 900F.
(v) Alternator : The gas turbine is coupled to the alternator.The alternator converts mechanical energy of the turbine into electrical energy.The output from the alternator is given to the bus-bars through transformer, circuit breakers and isolators.
(vi) Starting motor : Before starting the turbine, compressor has to be started. For this purpose,an electric motor is mounted on the same shaft as that of the turbine.The motor is energised by the batteries.Once the unit starts, a part of mechanical power of the turbine drives the compressor and there is no need of motor now.
Advantages of Gas turbine power plant :
Disadvantages of Gas turbine power plant:
A generating station which employs gas turbine as the prime mover for the generation of electrical energy is known as a gas turbine power plant.In a gas turbine power plant, air is used as the working fluid.The air is compressed by the compressor and is led to the combustion chamber where heat is added to air, thus raising its temperature.Heat is added to the compressed air either by burning fuel in the chamber or by the use of air heaters.The hot and high pressure air from the combustion chamber is then passed to the gas turbine where it expands and does the mechanical work. The gas turbine drives the alternator which converts mechanical energy into electrical energy.
It may be mentioned here that compressor, gas turbine and the alternator are mounted on the same shaft so that a part of mechanical power of the turbine can be utilised for the operation of the compressor.Gas turbine power plants are being used as standby plants for hydro-electric stations, as a starting plant for driving auxiliaries in power plants etc.
Schematic arrangement of a gas turbine power plant:
The schematic arrangement of a gas turbine power plant is shown in Figure below.
The main components of the plant are :
(i) Compressor
(ii) Regenerator
(iii) Combustion chamber
(iv) Gas turbine
(v) Alternator
(vi) Starting motor
(i) Compressor : The compressor used in the plant is generally of rotatory type.The air at atmospheric pressure is drawn by the compressor via the filter which removes the dust from air.The rotatory blades of the compressor push the air between stationary blades to raise its pressure.Thus air at high pressure is available at the output of the compressor.
(ii) Regenerator : A regenerator is a device which recovers heat from the exhaust gases of the turbine.The exhaust is passed through the regenerator before wasting to atmosphere. A regenerator consists of a nest of tubes contained in a shell.The compressed air from the compressor passes through the tubes on its way to the combustion chamber.In this way,compressed air is heated by the hot exhaust gases.
(iii) Combustion chamber : The air at high pressure from the compressor is led to the combustion chamber via the regenerator. In the combustion chamber, heat is added to the air by burning oil.The oil is injected through the burner into the chamber at high pressure to ensure atomisation of oil and its thorough mixing with air.The result is that the chamber attains a very high temperature (about 3000 F).The combustion gases are suitably cooled to 1300F to 1500F and then delivered to the gas turbine.
(iv) Gas turbine : The products of combustion consisting of a mixture of gases at high temperature and pressure are passed to the gas turbine.These gases in passing over the turbine blades expand and thus do the mechanical work. The temperature of the exhaust gases from the turbine is about 900F.
(v) Alternator : The gas turbine is coupled to the alternator.The alternator converts mechanical energy of the turbine into electrical energy.The output from the alternator is given to the bus-bars through transformer, circuit breakers and isolators.
(vi) Starting motor : Before starting the turbine, compressor has to be started. For this purpose,an electric motor is mounted on the same shaft as that of the turbine.The motor is energised by the batteries.Once the unit starts, a part of mechanical power of the turbine drives the compressor and there is no need of motor now.
Advantages of Gas turbine power plant :
- It is simple in design as compared to steam power station since no boilers and their auxiliaries are required.
- It is much smaller in size as compared to steam power station of the same capacity.This is expected since gas turbine power plant does not require boiler, feed water arrangement etc.
- The initial and operating costs are much lower than that of equivalent steam power station.
- It requires comparatively less water as no condenser is used.
- The maintenance charges are quite small.
- Gas turbines are much simpler in construction and operation than steam turbines.
- It can be started quickly form cold conditions.
- There are no standby losses.However, in a steam power station, these losses occur because boiler is kept in operation even when the steam turbine is supplying no load.
Disadvantages of Gas turbine power plant:
- There is a problem for starting the unit. It is because before starting the turbine, the compressor has to be operated for which power is required from some external source. However, once the unit starts, the external power is not needed as the turbine itself supplies the necessary power to the compressor.
- Since a greater part of power developed by the turbine is used in driving the compressor, the net output is low.
- The overall efficiency of such plants is low (about 20%) because the exhaust gases from the turbine contain sufficient heat.
- The temperature of combustion chamber is quite high (3000F) so that its life is comparatively reduced.
Schematic arrangement of a gas turbine power plant
4/
5
Oleh
Unknown
